Re: 紀錄資料約120Mbytes(斷電記憶),如何解決?
|
||||
---|---|---|---|---|
資深會員
|
參照:
這方面我沒接觸過,可以提供一些廠家型號參考嗎?
發表於: 2022/1/11 9:31
|
|||
|
Re: 紀錄資料約120Mbytes(斷電記憶),如何解決?
|
||||
---|---|---|---|---|
資深會員
|
參照:
你好,能提供型號嗎?
發表於: 2022/1/10 10:37
|
|||
|
Re: pic18f57k42燒錄時可以不將EEPROM寫入嗎?
|
||||
---|---|---|---|---|
資深會員
|
參照:
謝謝提供解答
發表於: 2021/11/9 8:24
|
|||
|
pic18f57k42燒錄時可以不將EEPROM寫入嗎?
|
||||
---|---|---|---|---|
資深會員
|
如題,因為測試時有些數據會寫入EEPROM,一旦修改程式重新燒錄時EEPROM會被清空(變成FF),有沒有辦法燒錄程式時不將EEPROM清除?
發表於: 2021/11/8 13:49
|
|||
|
藍芽5.0 速度 一對多?
|
||||
---|---|---|---|---|
資深會員
|
網路搜尋到藍芽5.0速度可達2Mbps,但都沒說到可不可以一對多?目前的應用是需四個裝置透過藍芽即時傳輸至手機,藍芽5.0速度是可以但不知可不可以手機對四個裝置?
發表於: 2021/11/3 8:56
|
|||
|
use mplabx ide interrupt subroutine for pic18f57k42
|
||||
---|---|---|---|---|
資深會員
|
之前使用Microchip MCU 都只有1或2個中斷副程式(一個High一個Low),如下
void __interrupt() int_sub(void) { } 目前剛好使用pic18f57k42看到datasheet裡頭有Interrupt Vector Table (IVT) 請問在mplabx ide(xc8),如何宣告及使用中斷副程式
發表於: 2021/8/11 9:56
|
|||
|
pickit4如何離線燒錄?
|
||||
---|---|---|---|---|
資深會員
|
pickit4上有MicroSD卡槽,但不知如何離線燒錄?
發表於: 2021/5/11 10:32
|
|||
|
pic16f1503 進入debug mode 出現error
|
||||
---|---|---|---|---|
資深會員
|
The following memory area(s) will be programmed:
program memory: start address = 0x0, end address = 0x41f configuration memory Verify of debug exec failed Could not enter debug mode because programming the debug information failed. Invalid combinations of config bits may cause this problem // PIC16F1503 Configuration Bit Settings // 'C' source line config statements // CONFIG1 #pragma config FOSC = INTOSC // Oscillator Selection Bits (INTOSC oscillator: I/O function on CLKIN pin) #pragma config WDTE = OFF // Watchdog Timer Enable (WDT disabled) #pragma config PWRTE = OFF//ON // Power-up Timer Enable (PWRT enabled) #pragma config MCLRE = OFF // MCLR Pin Function Select (MCLR/VPP pin function is digital input) #pragma config CP = OFF // Flash Program Memory Code Protection (Program memory code protection is disabled) #pragma config BOREN = OFF // Brown-out Reset Enable (Brown-out Reset disabled) #pragma config CLKOUTEN = OFF // Clock Out Enable (CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin) // CONFIG2 #pragma config WRT = OFF // Flash Memory Self-Write Protection (Write protection off) #pragma config STVREN = ON // Stack Overflow/Underflow Reset Enable (Stack Overflow or Underflow will cause a Reset) #pragma config BORV = LO // Brown-out Reset Voltage Selection (Brown-out Reset Voltage (Vbor), low trip point selected.) #pragma config LPBOR = OFF // Low-Power Brown Out Reset (Low-Power BOR is disabled) #pragma config LVP = ON // Low-Voltage Programming Enable (Low-voltage programming enabled) // #pragma config statements should precede project file includes. // Use project enums instead of #define for ON and OFF. #include 請問哪邊設定要改?
發表於: 2021/1/27 14:43
|
|||
|
Re: i2c for pic16f946(SSP)?
|
|
|||
---|---|---|---|---|
資深會員
|
發表於: 2020/4/9 16:04
|
|||
|