謝謝您的建議~! 我會考慮去報名的~! ^^

至於無法啟動的問題已經解決了~!我加上INITIAL MCU的參數就OK了~!

感謝高手指點~~ 有機會再跟你們請教~!

謝謝您的回應~!

只是有一點我不了解，就是為何OUTPUT要加隔離?要怎麼加?
當我ICD2只有接USB當資料傳輸間電源時。MCLR也會產生DC 12~13V的電壓去燒錄嗎?

謝謝您快速的回應~!

謝謝版主的提示，可是我不知道要如何才能產生.HEX檔勒~!還有要去CONFIG裡設定什麼呢? (我真糟糕 ><)

請問: 我接一個4MHz的XTAL還有兩個104接地，降子可以嗎?
(我是自己依照ICD2的說明書自己做ㄧ個電路板的!! 板子上只有PIC MCU 還有一個電源座 還有電話母座! 降子OK嗎??)

請問: 我剛買到ICD2 我按照它附的說明書上電話線跟PIC MCU接腳的方式去做了一個電路板。沒錯，那電路板只有ZIP跟電源座還有6P6C2的電話母座。

降子可以做DEBUG & PROGRAM 程式嗎?

兩天前剛買到 ICD 2，我用PIC16F819先做LED測試。

Connecting to MPLAB ICD 2
...Connected
Setting Vdd source to MPLAB ICD 2
Target Device PIC16F819 found, revision = Rev 0x5
...Reading ICD Product ID
Running ICD Self Test
...Passed
MPLAB ICD 2 Ready

但都無法進入DEBUG的模式去測試。我的程式BUILD ALL 有過，如下所示:

Clean: Deleting intermediary and output files.
Clean: Deleted file "D:\MPLAB\PIC16F819\LED_TEST\LED_TEST.o".
Clean: Deleted file "D:\MPLAB\PIC16F819\LED_TEST\LED_TEST.ERR".
Clean: Deleted file "LED_TEST.lst".
Clean: Done.
Executing: "C:\Program Files\Microchip\MPASM Suite\MPAsmWin.exe" /q /p16F819 "LED_TEST.asm" /l"LED_TEST.lst" /e"LED_TEST.err" /o"LED_TEST.o"
Executing: "C:\Program Files\Microchip\MPASM Suite\MPLink.exe" "D:\MPLAB\PIC16F819\LED_TEST\16f819.lkr" "D:\MPLAB\PIC16F819\LED_TEST\LED_TEST.o" /o"LED_TEST.cof" /M"LED_TEST.map"
MPLINK 4.00, Linker
Copyright (c) 2005 Microchip Technology Inc.
Error - section '.org_0' can not fit the absolute section. Section '.org_0' start=0x00000000, length=0x00000034

BUILD FAILED: Fri Nov 11 15:26:34 2005

但PROGRAM時總是出現以下的訊息:

Programming Target...
...Validating configuration fields
...Erasing Part
...Loading DebugExecutive
...Programming DebugExecutive
...Programming Debug Vector
Verifying...
...Debug Executive
...Debug Vector
...Verify Succeeded
Programming Configuration Bits
.. Config Memory
Verifying configuration memory...
...Verify Succeeded
ICD0083: Target not in debug mode, unable to perform operation
MPLAB ICD 2 Ready

請各位高手幫幫忙~!