Re: dsPIC33CK256MP205時,使用內振FRC Oscillator頻率不準
|
||||
---|---|---|---|---|
新會員
|
版主您好,
收到了,謝謝您的回覆~~ MCU:dsPIC33CK256MP205 C編譯器版本:XC16V2.00
發表於: 2022/11/3 11:47
|
|||
|
Re: dsPIC33CK256MP205時,使用內振FRC Oscillator頻率不準
|
||||
---|---|---|---|---|
新會員
|
版主您好,
感謝您的回覆,我有試過您說的方式在dsPIC33CK256MP205上使用和dsPIC33CK Curiosity Development Board相同的MCC設定方式,查看PWM輸出是(81.6KHz)不正確的,然後我也有試過手邊另一塊焊有dsPIC33CK256MP205板子,將同樣的程式燒入,查看PWM輸出是(100KHz)正確的,所以我確定是dsPIC33CK256MP205板子的問題,只是不知道為什麼這片dsPIC33CK256MP205板子的內振FRC Oscillator會不準? 使用元件:dsPICCK256MP205 ,C編譯器版本:XC16V2.00
發表於: 2022/10/28 13:32
|
|||
|
dsPIC33CK256MP205時,使用內振FRC Oscillator頻率不準
|
||||
---|---|---|---|---|
新會員
|
版主您好,
最近使用MPLAB XIDE V6.00在開發dsPIC33CK256MP205時,使用內振FRC Oscillator設定16MHz當主頻, 周邊使用PWM設定100KHz的頻率,使用Logic Analyzer抓取pwm訊號量測出的頻率為81.6KHz,請問需要校正嗎? 或要從哪裡校正?手邊有另一個開發板dsPIC33CK Curiosity Development Board同樣是設內振FRC Oscillator 設定16MHz當主頻,周邊使用PWM設定100KHz的頻率,使用Logic Analyzer抓取pwm訊號量測出的頻率為100KHz 是準的... MCU:dsPIC33CK256MP205 C編譯器版本:XC16V2.00
發表於: 2022/10/27 17:04
|
|||
|
Re: PICKIT4 無法debug
|
||||
---|---|---|---|---|
新會員
|
Darren您好,
了解,今天會將PICKIT4寄出到代理商(華豫寧)那裏,代理商會幫忙轉寄, 謝謝您的回覆~~
發表於: 2022/4/12 16:12
|
|||
|
Re: PICKIT4 無法debug
|
||||
---|---|---|---|---|
新會員
|
KevinLu 您好,
我已經有更換USB傳輸線並使用 "Hardware Tool Emergency Firmware Boot Recovery Utility"回復原廠設定,進入debug mode時還是會出現下面訊息 Reception on endpoint 129 failed (err = -10121) Reception on endpoint 129 failed (err = -10121) A communication error with the debug tool has occurred. The tool will attempt to recover momentarily. Unable to run the target device. Transmission on endpoint 2 failed (err = -10121) 請問可以送修嗎? 手上有PICKIT3進入debug mode是沒有問題的!!
發表於: 2022/4/12 11:40
|
|||
|
PICKIT4 無法debug
|
||||
---|---|---|---|---|
新會員
|
各位先進,
想請問,我的PICKIT4之前使用都正常,可是最近使用,可以進入debug mode,可是無法debug,會出現下面的錯誤訊息,有辦法可以修復嗎!! (我已經有做了回復原廠設定了) Reception on endpoint 129 failed (err = -10121) A communication error with the debug tool has occurred. The tool will attempt to recover momentarily. 我使用的XIDE V5.30版 mcu:PIC16F19156 xc8:V2.10版
發表於: 2022/4/8 10:03
|
|||
|