Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
高級會員
|
11.0592MHz使用Timer 1產生鮑率, 最高只能到57.6K
11.0592MHz使用Timer 2產生鮑率, 最高能到115.2K 22.1184MHz使用Timer 1產生鮑率, 最高能到115.2K 22.1184MHz使用Timer 2產生鮑率, 最高能到115.2K 24MHz使用Timer 1產生鮑率, 最高只能到14.4k 24MHz使用Timer 2產生鮑率, 最高只能到57.6K
發表於: 2007/8/6 11:09
|
|||
|
Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
高級會員
|
8051/8052跑22.1184mhz都可以找到115.2k的鮑率
不知 11.0592MHz 是否也可以找到115.2k的鮑率??
發表於: 2007/8/6 10:14
|
|||
IWC
IWC JL Rolex PP 有點距離 越來越遠 |
||||
|
Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
高級會員
|
外掛24LCxxx的EEPROM來儲存, 串列傳輸速度較慢
而且寫入時間較長 因此不考慮 8051外掛ram讀寫比較快 原因是8051/8052跑22.1184mhz都可以找到115.2k的鮑率 而且速度也不慢(因為接近24mhx了)
發表於: 2007/8/3 16:57
|
|||
|
Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
版主
|
我也有藉口,RAM 不夠大儲存燒錄料可以用外掛24LCxxx的EEPROM來儲存,將要燒錄的資料copy到EEPROM哩,即使關機後只要重開就可以燒錄在 Download。這樣好不好。
不知為什麼要Run在22.118MHz?
發表於: 2007/8/3 16:18
|
|||
|
Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
高級會員
|
PIC24FJ 輸出只有3.3V (Vdd), 給8051讀應該是沒問題的
雙向也沒有問題 手上沒有3.3V的8051, 查了一下AT89LS52只能跑到16MHz 可是我要跑到22.1184MHz PIC18Fxxxx 和PIC24FJ16GA002 內部ram不夠大 還是8051比較熟....(藉口很多....呵呵)
發表於: 2007/8/3 15:33
|
|||
|
Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
版主
|
PIC24FJ 是3.3V 元件,Vdd 只能給 3.3V,Digital I/O 是可以承受到5V輸入,但輸出也只有3.3V (Vdd)。EMUD1 是雙向的。
要不要找個3.3V的 80c51就解決了。或直接用PIC18Fxxxx 甚至就用 PIC24FJ16GA002 來做燒錄器。
發表於: 2007/8/3 15:03
|
|||
|
Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
高級會員
|
PIC24FJ64GA002的電源是用獨立的3.3v
我現在不用icd2燒錄 而是我想自己做燒錄器 燒錄器是用8051設計 但是8051的輸出邏輯準位和PIC24FJ不一樣 我不想在邏輯準位轉換上用太複雜的電路去設計 因此我想直接就接上去 但是又怕PIC24FJ會被損壞 所以想找到一組耐壓可以達到5v的輸出入腳 我找到了第2和第3組燒錄腳 請問我的結論有誤嗎?
發表於: 2007/8/3 14:16
|
|||
|
Re: PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
版主
|
3.3V 的元件燒錄不管使用哪一組,我都是外加3.3V的讀第電源,不要將ICD2的電源送給Target Board.
可以從 Debug --> Status --> Power 選項將 ICD2送出去的 Power 關掉。
發表於: 2007/8/3 13:38
|
|||
|
PIC24FJ64GA002的燒錄問題
|
||||
---|---|---|---|---|
高級會員
|
PIC24FJ64GA002的電源是使用3.3V,燒錄腳位有3組,如果我要使用(0V, 5V)的邏輯準位當作PGC和PGD的信號(PGC和PGD實際上是由8051的P1.7和P1.6加4.7K提升電阻來產生),我記得類比的輸入腳是不可以超過VDD + 0.3V,純粹數位的輸入腳是可以到+6.0V,經檢查發現,PGC1/PGD1也是AN2/AN3,所以PGC1/PGD1這組我不可以用,但PGC2/PGD2和PGC3/PGD3卻是純粹是數位輸入腳,因此PGC2/PGD2和PGC3/PGD3我可以用8051的I/O腳驅動而不會損害PIC24FJ64GA002。請問以上的結論是否有誤?
發表於: 2007/8/3 13:19
|
|||
|