:::
Browsing this Thread:
1 Anonymous Users
|
Re: PICDEM Mechatronics編譯問題
|
||||
|---|---|---|---|---|
|
版主
 
|
參照：
PIC16F690 因是低成本的元件，本身並不含有ICD除錯模組，所以要另外使用一轉接座 AC162061 來除錯。 如果沒有此專接座的話就只能用燒錄的方式並配合MPLAB SIM 的模擬方式來除錯了。
發表於: 2009/10/5 11:11
|
|||
|
||||
|
Re: PICDEM Mechatronics編譯問題
|
||||
|---|---|---|---|---|
|
資深會員
 
|
看看是不是振盪器設錯了
發表於: 2009/10/2 8:13
|
|||
|
||||
|
Re: PICDEM Mechatronics編譯問題
|
||||
|---|---|---|---|---|
|
新會員
 
|
我依照板大建議後更改了設定
編譯部分是沒問題了，可以編譯成功\r 但是燒入時卻失敗出現了問題! 出現一下訊息!! MPLAB ICD 2 ready for next operation Programming Target... ...Validating configuration fields ...Erasing Part ...Programming Program Memory (0x0 - 0x63) ...Loading DebugExecutive ...Programming DebugExecutive ...Programming Debug Vector Verifying... ...Program Memory ...Debug Executive ...Debug Vector ...Verify Succeeded Programming Configuration Bits .. Config Memory Verifying configuration memory... ...Verify Succeeded Connecting to debug executive ICD0083: Debug: Unable to enter debug mode. Please double click this message for more information. MPLAB ICD 2 ready for next operation
發表於: 2009/10/1 16:41
|
|||
|
||||
|
Re: PICDEM Mechatronics編譯問題
|
||||
|---|---|---|---|---|
|
版主
|
PIC16F690 ???
查一下以前叫做 _BOD_OFF，新版的改成 _BOR_xxx 了，請參考 p16F690.inc 檔的定義: ;========================================================================== ; ; Configuration Bits ; ;========================================================================== _FCMEN_ON EQU H'3FFF' _FCMEN_OFF EQU H'37FF' _IESO_ON EQU H'3FFF' _IESO_OFF EQU H'3BFF' _BOR_ON EQU H'3FFF' _BOR_NSLEEP EQU H'3EFF' _BOR_SBODEN EQU H'3DFF' _BOR_OFF EQU H'3CFF' _CPD_ON EQU H'3F7F'
發表於: 2009/9/25 15:12
|
|||
|
||||
|
PICDEM Mechatronics編譯問題
|
||||
|---|---|---|---|---|
|
新會員
|
網路學員PICDEM Mechatronics所附的範例程式(Project9)
編譯時一直沒辦法成功,不知道是哪邊出了問題? Clean: Deleting intermediary and output files. Clean Warning: File "ECCP.err" doesn't exist. Clean Warning: File "C:\Mechatronics\firmware\Lesson9\ECCP.cod" doesn't exist. Clean Warning: File "C:\Mechatronics\firmware\Lesson9\ECCP.hex" doesn't exist. Clean Warning: File "ECCP.lst" doesn't exist. Clean: Deleted file "D:\RTC\Elite\PICDEM Mechatronics\firmware\Project9\eccp.mcs". Clean: Done. Executing: "D:\Program Files\Microchip\MPASM Suite\MPASMWIN.exe" /q /p16F690 "ECCP.asm" /l"ECCP.lst" /e"ECCP.err" /d__DEBUG=1 Error[113] D:\RTC\ELITE\PICDEM MECHATRONICS\FIRMWARE\PROJECT9\ECCP.INC 3 : Symbol not previously defined (_BOD_OFF) Halting build on first failure as requested. ---------------------------------------------------------------------- BUILD FAILED Attach file: Link only for registered users
發表於: 2009/9/25 11:08
|
|||
|
||||
You can view topic.
你 不可以 發起新主題
You cannot reply to posts.
You cannot edit your posts.
You cannot delete your posts.
You cannot add new polls.
You cannot vote in polls.
You cannot attach files to posts.
You cannot post without approval.
You cannot use topic type.
You cannot use HTML syntax.
You cannot use signature.
You cannot create PDF files.
You cannot get print page.
