Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
版主
|
發表於: 2006/6/30 9:26
|
|||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
中級會員
|
我用的是 33p 2 個 加上 10MHz crystal .
是否有電路圖可以剪來參考, 我想只作一片含括MCLR 外部振盪器 及電話接頭 的最小功能實驗板 ( LCD , LED , sensor 等 考慮 外接 ) , 謝謝 .
發表於: 2006/6/30 9:03
|
|||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
新會員
|
應該是電容值接錯,電容值錯誤震盪器無法正常震盪
發表於: 2006/6/29 16:16
|
|||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
中級會員
|
已設為 HS , 不過晚上回家後會再檢查看看 , 謝謝 .
還是不通 , 改了一些電路 , 全掛了 . 只好再重作一塊板子了 . 不管如何 , 仍然謝謝各位的指導 .
發表於: 2006/6/27 9:28
|
|||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
版主
|
石英震盪器沒有震盪,檢查Configuration 的設定。
發表於: 2006/6/27 9:20
|
|||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
中級會員
|
好的 , 晚一點 會剪下, 先請各位休息 , 我再對一對線路圖 (我是
依照 PIC18F452 C Advance Training Board 作的 ) Connecting to MPLAB ICD 2 ...Connected Setting Vdd source to target Target Device PIC18F452 found, revision = b5 ...Reading ICD Product ID Running ICD Self Test ...Passed MPLAB ICD 2 Ready Resetting Target MPLAB ICD 2 Ready Programming Target... ...Validating configuration fields ...Erasing Part ...Programming Program Memory (0x0 - 0x2F) ...Loading DebugExecutive ...Programming DebugExecutive ...Programming Debug Vector ...Programming RSBUG Verifying... ...Program Memory ...Debug Executive ...Debug Vector ...Verify Succeeded Programming Configuration Bits .. Config Memory Verifying configuration memory... ...Verify Succeeded Connecting to debug executive ICD0083: Debug: Unable to enter debug mode. Please double click this message for more information. MPLAB ICD 2 Ready
發表於: 2006/6/26 17:17
|
|||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
版主
|
你說 "Programmer mode 可以 燒錄 Debug mode 時 可以 build all 但燒錄時有 bug" 燒錄時出現什麼樣的 bug 可不可以將 output window 的錯誤訊息剪出來看看是何種問題?
發表於: 2006/6/26 16:29
|
|||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
高級會員
|
發表於: 2006/6/26 16:25
|
|||
微電腦自動控制設計,產品製造
才疏學淺,若有錯誤敬請指正 |
||||
|
Re: 自己作demo board 就是不通
|
||||
---|---|---|---|---|
中級會員
|
RB6 , RB7 僅用於 ICD2 電話線的 第2,3 腳 (PGC 及 PGD )
發表於: 2006/6/26 16:15
|
|||
|