Re: 求助:rfPIC12F675的烧写问题
|
||||
---|---|---|---|---|
資深會員
|
没错,这样就算是link 成功,但是你已经将 osc 的校正值给洗掉了。(不要校正是无妨,如果要校正,在那拿到新ic前,要先将校正值读出,然后写在ic上,以防不小心洗掉。
發表於: 2007/1/26 17:56
|
|||
|
Re: 求助:rfPIC12F675的烧写问题
|
||||
---|---|---|---|---|
版主
|
照你最上面所提與ICD2的接法是對的,照理說ICD2就應該可以編程 rfPIC12F675 。要不要找另一顆 PIC12F675 新用 ICD2 編程看看(MCLR 不要設為 Input I/O) , 可以的話再來測試 rfPIC12F675,也有可能 rdPIC12F675 壞了。
發表於: 2007/1/26 13:50
|
|||
|
Re: 求助:rfPIC12F675的烧写问题
|
||||
---|---|---|---|---|
新會員
|
我是PIC新手,现在毕业设计用到这个片子,不能写程序,很着急。想请教如何制作你所说的“转接座”?跟我1楼中直接连接的方法有什么本质上的区别?为什么要做这个转接座?1楼里我的接法实质上不也是针对PIC12F675的引脚烧写的吗?拜托版主告诉我具体一点的操作。谢谢。
發表於: 2007/1/26 12:28
|
|||
|
Re: 求助:rfPIC12F675的烧写问题
|
||||
---|---|---|---|---|
版主
|
rfPIC12F675 為 Dial Die 的設計,一為RF晶片,另一為 PIC12F675,兩個 DIE 獨立分開。所以 PICStart Plus 要燒錄 rfPIC12F675 只要針對PIC12F675的接腳燒就可以了,所以要做一個rfPIC12F675轉PIC12F675的轉接座。
發表於: 2007/1/26 9:20
|
|||
|
Re: 求助:rfPIC12F675的烧写问题
|
||||
---|---|---|---|---|
新會員
|
首先感谢Ryang版主的回答。
不过,我现在的问题是:在没有烧写任何程序的时候,通过UBS连接ICD2的六芯扁平线连接目标板在线烧写,设备ID号不能正确识别。当然不知道rfPIC12F675这颗片子出厂时,其/MCRL引脚是否写为I/O。 另外,我打开IDE7.5看过了,选择设备为rfPIC12F675时,PICStart Plus烧录器为红色,不能烧写。
發表於: 2007/1/25 21:05
|
|||
|
Re: 求助:rfPIC12F675的烧写问题
|
||||
---|---|---|---|---|
版主
|
ICD2 是可以編程rfPIC16F675的,不過先前已經將MCLR(GP3) 編程為GP3的話,ICD2 就無法對 rfPIC16F675 重新編程,因為 MCLR 功能消失,PIC 無法進入編程模式。遇到此種情形可以使用 PICStart Plus來編程或暫時不要使用GP3的功能讓這隻腳一直都維持在 MCLR 的功能。
發表於: 2007/1/25 10:10
|
|||
|
求助:rfPIC12F675的烧写问题
|
||||
---|---|---|---|---|
新會員
|
希望有实际用过这颗芯片的朋友帮忙:
使用MPLAB IDE7.5+MPLAB ICD2烧写错误:不能识别设备ID 号,期望值为0X7E,读取值为0X1FF。 硬件连接: 1 Vdd--+5V; 20 Vss---GND; 2 GP3----Vpp; 18 GP1-----CLK; 19 GP0-----Data Vdd接100PF电容后接地。 在其它论坛上看到有人有ICD2可以烧写rfPIC12F675,但是我现在遇到的却是根本不识别!!(曾经用过rfPIC12F675F和rfPIC12F675H两种,都是同样的结果)打电话问MICROCHIP技术支持,回答也说ICD2是可以烧写程序的,只是不能在线Debug而已。但实事上,我遇到了这样的问题。请教有使用经验的朋友!感谢!
發表於: 2007/1/24 21:55
|
|||
|