Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
版主
|
以 Vdd 為例 250mA 是最大的加總電流,也就是說從VDD流入PIC的電流不可超過250mA,從VSS流出的電流總量不可超過300mA。此PIC的最大消耗功率不可超過0.8W.
發表於: 2007/4/23 18:49
|
|||
|
Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
高級會員
|
謝謝,
請問In the pic16f87x datasheet electrical characteristics, Max current out of Vss pin is 300mA and Max current into Vdd pin is 250mA 這兩個max電流值是指Vss及Vdd 還沒combined的電流嗎? Thank you very much.
發表於: 2007/4/23 15:29
|
|||
|
Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
版主
|
每隻I/O腳最大電流為25mA, 但有些限制 PORTA , PORTB & PORTC 加起來 Source & Sink 分開加總後不可以超過200mA
發表於: 2007/4/23 14:58
|
|||
|
Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
高級會員
|
請問:
In the datasheet ch15.0 Electrical Characterics, Max output current sink(source) by any i/o port is 25mA, and Max current sink(source) by PORTA,PORTB,PORTD(Combined) is 200mA. 這段話什麼意思呢?為什麼說每一個I/O 的電流為25mA,PORT combined 後卻能達200mA呢? Thank you very much.
發表於: 2007/4/23 14:46
|
|||
|
Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
版主
|
假設一個 VDD pin 最大承受電流為10mA , 理論上兩支 VDD 腳相加後相對就可承受 200mA 的電流。
SOURCE CURRENT 及 SINK CURRENT 最大還是在 25mA。
發表於: 2007/4/23 14:27
|
|||
|
Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
高級會員
|
請問:
增加的電流指什麼電流呢? 是PORT的SOURCE CURRENT 及SINK CURRENT嗎? Thank you very much.
發表於: 2007/4/23 13:48
|
|||
|
Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
版主
|
看一下Data Sheet 第十五章 的電氣特性裡有描述,PORTA, PORTB and PORTE 為共用電源腳,最大總和電流為200mA已內,而PORTC & PORTD 也為200mA。16F877共有兩腳Vdd & Vss 這是為增加電流所設計的,而且 Vcc & Vss Pad 不只打一條線。
發表於: 2007/4/23 9:34
|
|||
|
Re: 為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
高級會員
|
之前有一篇文章有問過這個問題 有蠻詳細的解答
不過我忘了是哪篇 如果沒記錯好像是 分擔內部電路的電壓 還是 隔絕一些問題 不好意思 我這樣回答好像跟沒回答一樣 建議 翻一下舊文 應該會找到答案
發表於: 2007/4/21 4:20
|
|||
|
為什麼PIC16F877上有VDD PIN 腳有兩個?
|
||||
---|---|---|---|---|
高級會員
|
Dear all,
為什麼PIC16F877上VDD PIN 及VSS PIN腳各有兩個? 是什麼原因會這樣設計呢? Thanks very much.
發表於: 2007/4/20 16:06
|
|||
|