Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
版主
|
F/W 換過後還是依樣嗎?
MPLAB IDE 重新啟動後,會不會有相同的問題發生?
發表於: 2007/8/3 10:43
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
中級會員
|
參照:
MPLAB IDE 的版本7.52 ICD2 Firmware換新的ICD2,ICD2會重新Download Firmware。 也有在操作過程中於Debug模式下重新下載ICD2 Firmware。
發表於: 2007/8/3 10:36
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
版主
|
MPLAB IDE 的版本為何? 試一下在 Debug 選項下更新 Operation OS ( ICD2 Firmware)。
發表於: 2007/8/2 9:52
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
中級會員
|
參照:
我使用pic 16f946 做ICD2 的debug時出現下列訊息: ICD0031: API: Framing error ICD0151: Failed to sync memory (MT = Data) (Dir = 0x0) ICD0082: Failed MPLAB ICD 2 operation ICD0082: Failed MPLAB ICD 2 operation 重新連線後,可執行,但是如果執行BreakPoint則是產生以上問題。 ICD2換過兩台,其中ㄧ台為未拆封的,所得出的結果是相同的。 不知這是什麼問題產生的。
發表於: 2007/8/2 7:31
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
版主
|
ICD0031的錯誤,照MPLAB IDE help裏的說明是 :MPLAB IDE and MPLAB ICD 2 are out of synch with each other. Here are some common reasons and corrective actions.
Reconnect to the MPLAB ICD 2. Try the operation again. It is possible the error was a one time glitch. The version of MPLAB IDE installed may be incorrect for the version of firmware loaded on the MPLAB ICD 2. Follow the steps outlined in <General Corrupted Installation Actions>, and then manually download the MPLAB ICD 2 Operating System. If the problem persists contact Microchip. 所以先更新ICD2的Operation System, 如果還是不行連線請送修。
發表於: 2007/5/4 11:09
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
新會員
|
你能否先用ICD2光盘的范例调试一下。
發表於: 2007/5/4 10:52
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
新會員
|
不好意思~~
我再做debug時,還是會顯示這些訊息: ICD0031: API: Framing error ICD0151: Failed to sync memory (MT = Data) (Dir = 0x0) ICD0082: Failed MPLAB ICD 2 operation ICD0082: Failed MPLAB ICD 2 operation 不曉得最大的問題出在哪裡? 請大大能再給我一些建議!!謝謝
發表於: 2007/5/2 15:46
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
版主
|
; The definitions and variants for the configuration bits are found in the
我是這樣設定的。 Download 新的 OS 可以在 Project 目錄下找到。
發表於: 2007/5/2 13:47
|
|||
|
Re: PIC 16f886使用ICD2 debug的問題
|
||||
---|---|---|---|---|
新會員
|
1.我用的是MPLAB IDE v7.52 的版本,那7.52版附屬ICD2 OS download 就是新的還是說要另外下載更新檔更新. .
2.我的震盪也是為Inter-RC,若要檢查是否有震盪,是檢查ICD2的clock接腳是否有傳到PIC內嗎?? 謝謝.....
發表於: 2007/5/2 13:08
|
|||
|