Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
高級會員
|
哈哈 , 和 yiming 大大 真有默契 , 都同時回答同一問題!
"感覺上還是訊息不足,想太多就走火入魔了" ==> 是阿 , 你本來回應的是對的 , 怎又改為 "並聯"了 ??
發表於: 2009/5/13 11:40
|
|||
|
Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
高級會員
|
何謂"待測負載" ??
我覺得是 "待測電導" , 200mV是加在這個的二端的 Attach file: (0.00 KB)
發表於: 2009/5/13 11:33
|
|||
|
Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
資深會員
|
所謂回授電阻就是由輸出端接個電阻回到輸入端...
....................回授電阻
感覺上還是訊息不足,想太多就走火入魔了
發表於: 2009/5/13 11:28
|
|||
|
Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
資深會員
|
[/quote]
當然有和 "待測電導" 串聯 , 否則 電流I 怎會相同 !! [/quote] 說的也是,我現在把他想像成一個 200mV 的電壓源,串聯一個 1MΩ 電阻,再串聯"待測負載"後接地。 這樣我可以在"待測負載"的兩端得到電壓並用OP放大輸出,可是文章中又說 1MΩ 電阻是一個 feedback resistor,也就是下面這一段: In the device, the Current (I) flows through a 1megOhm feedback resistor to produce the Output Voltage (Vout), so that: 迴授電阻如何可以和"待測負載"串聯呢?這邊的邏輯搞不清楚了,請問大大們認為如何呢?Thanks!
發表於: 2009/5/13 11:06
|
|||
|
Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
高級會員
|
參照:
當然有和 "待測電導" 串聯 , 否則 電流I 怎會相同 !! I = 200mV * G = Vout * 1/1MΩ = Vout * 1u => G = Vout * 1u/200mV = Vout * 5u
發表於: 2009/5/13 10:32
|
|||
|
Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
資深會員
|
多謝兩位高手的指導!
請問大大們認為那個 1MΩ 電阻到底是接在哪裡呢? 有和負載串聯嗎,想很久都不解其意。
發表於: 2009/5/13 9:50
|
|||
|
Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
資深會員
|
Conductance (G), as expressed in units
known as Siemens, is the inverse of Resistance (R): 譯文:電導的單位是用 Siemens 來表示,也就是電阻的倒數。 G = 1 / R //以上為電導的定義 正確無誤 The device presents a voltage of 200mV across the resistance being measured, so that the Current (I) flowing across the load from one electrode to the other is equal to applied voltage divided by the resistance: 譯文:這個裝置提供一個 200mV 的電壓通過一個被量測過的電阻,這樣一來流過在兩個電極之間所接負載的電流就等於是電壓除以電阻。 //簡單說就是 I=V/R=V*G I = 200mv / R = 200mV × G ......(1) In the device, the Current (I) flows through a 1megOhm feedback resistor to produce the Output Voltage (Vout), so that: //這裡只是要套出一個式子,沒提供清楚的訊息是什麼電路 //只能就所提供的公式來明白他的推導過程 Vout = I *Rfeedback (電阻值1M歐姆) = I × 1 megOhm (套用上面 式子(1)) = 200mV × G × 1megOhm (整理一下就變成下面的解答了) Solving for Conductance (G): 譯文:電導的解答: G = Vout / 0.200V × 1megOhm (套用電導的定義會變成下面的式子) Since 1 megOhm is the reciprocal of 1 μSiemens, the Conductance (G), in μSiemens, is equal to 5 times the Output Voltage: 譯文:因為 1MΩ 等於 1 μSiemens 的倒數,所以電導 μSiemens 等於 5 倍的輸出電壓,公式如下: G (μSiemens) = 5 . Vout Therefore, for the device, 1 Volt of output equals 5 μSiemens. This relationship along with the calibration function of the recording device can be used to convert the voltages recorded from the subject to μSiemens of conductance. 最後假設 Vout=1V那麼 電導=5μ (Siemens) //因為題目給的資訊不夠,它又只是要做一個怪怪的推導而已 //去探討他是什麼電路反而就走不出來了 //感覺上很像是一個回授型的放大電路 //總之他憑空生出了 Vout = I * Rfeedback 這條式子 //再接著推導就變成了最後的結果了 //什麼怪題目 XD
發表於: 2009/5/12 14:04
Edited by yiming on 2009年05月12日 15:55:14
Edited by yiming on 2009年05月12日 15:56:03 Edited by yiming on 2009年05月12日 16:10:01 Edited by yiming on 2009年05月12日 16:17:51 |
|||
|
Re: 可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
高級會員
|
參照:
我不確定對不對 , 但這個裝置應該是提供一個 "定電壓" 源(200mV),流過待測電導,產生的電流亦流過一個迴授電阻 (1MΩ ),並利用量測迴授電阻的電壓(Vout)來計算出待測電導的值是多少! 利用定電壓 (200mV) 與 定電阻 (1MΩ ) 的倒數差5倍,求出公式 G (μSiemens) = 5 . Vout
發表於: 2009/5/12 14:01
|
|||
|
可否請教一下這篇有關電導的英文定義為何?
|
||||
---|---|---|---|---|
資深會員
|
大家好:
以下是一篇有關電導的英文說明,由於有些地方我看的似懂非懂,所以想請大家幫我看看翻譯的地方對不對,還有就是這個電路應該長什麼樣子,是一個電壓分配定理的電路呢?還是一個OP放大的電路?謝謝。 Conductance (G), as expressed in units known as Siemens, is the inverse of Resistance (R): 譯文:電導的單位是用 Siemens 來表示,也就是電阻的倒數。 G = 1 / R The device presents a voltage of 200mV across the resistance being measured, so that the Current (I) flowing across the load from one electrode to the other is equal to applied voltage divided by the resistance: 譯文:這個裝置提供一個 200mV 的電壓通過一個被量測過的電阻,這樣一來流過在兩個電極之間所接負載的電流就等於是和電阻的分壓。 I = 200mv / R = 200mV × G In the device, the Current (I) flows through a 1megOhm feedback resistor to produce the Output Voltage (Vout), so that: 譯文:在這個裝置,電流流經一個1MΩ的迴授電阻來產生一個輸出電壓,公式如下: Vout = 1 / Rfeedback = I × 1 megOhm = 200mV × G × 1megOhm Solving for Conductance (G): 譯文:電導的解答: G = Vout / 0.200V × 1megOhm Since 1 megOhm is the reciprocal of 1 μSiemens, the Conductance (G), in μSiemens, is equal to 5 times the Output Voltage: 譯文:因為 1MΩ 等於 1 μSiemens 的倒數,所以電導 μSiemens 等於 5 倍的輸出電壓,公式如下: G (μSiemens) = 5 . Vout Therefore, for the device, 1 Volt of output equals 5 μSiemens. This relationship along with the calibration function of the recording device can be used to convert the voltages recorded from the subject to μSiemens of conductance. 譯文:因此就這個裝置而言,1V 輸出就等於 5 μSiemens,這和校正功能以及可以轉換電壓並記錄的裝置有關係。 以上可否幫我看一下意思是否正確?還有這個電路的結構是否是 200mV 通過一個 1MΩ 電阻和負載後,當放大電壓為 1V 時,電導就是 5 μSiemens 的意思嗎?謝謝耐心看完。
發表於: 2009/5/12 11:33
|
|||
|