Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
新會員
|
可能要更新一下,下載到ICD2的Firmware
Please check the note at: http://www.microchip.com/stellent/idc ... me=en019469&part=SW007002 ======================== FW08 for MPLAB ICD 2 Microchip has updated the firmware (FW08) to improve the robustness of this programming algorithm. The following devices are affected: 16F785, 16F68X/690, 16F636/639, 12F635/683, 16F91X/946. ================================ 下載檔案在: http://ww1.microchip.com/downloads/en/DeviceDoc/ICD08010403.hex
發表於: 2006/5/22 10:01
|
|||
|
Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
中級會員
|
這個情況我常遇到,以我的經驗這是電話線到你的chip中間阻抗太大,常是接觸不良所引起,或者你可試著縮短這段路徑。
發表於: 2006/5/5 10:47
|
|||
|
Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
版主
|
檢查一下6-pin 的電話線接頭是否接觸不良,MCLR pin 是否接了電容器?Target Board有電源嗎?
發表於: 2006/5/3 17:14
|
|||
|
Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
初級會員
|
妳確定一下ICD2有沒有接上9v DC,還有MPLAB中,PROGRAMMER SETTING中的POWER選項, power target from MPLAB ICD2有沒有打勾起來, configuration bits中,把功能disable掉試試看.
發表於: 2006/5/3 15:26
|
|||
|
Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
初級會員
|
謝謝大大的建議!
不過我可以確定icd2沒問題,因為我也用它來燒pic16f684就沒問題。所以因該不是電腦的問題或是icd2的問題。 那至於設定上的問題,我也確定了好幾次了,也都沒問題才進行燒錄。所以因該也不是。 本以為是我的mplab ide6.61版的問題,不過我又去下載了7.30版,結果還是一樣。真是奇怪了。
發表於: 2006/5/2 15:34
|
|||
|
Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
初級會員
|
先確定你在configure/select device
選的PIC是正確的 之前我選錯也是有這個訊息
發表於: 2006/4/30 1:06
|
|||
|
Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
資深會員
|
建議您先換顆晶片試試,若是一樣的結果;再試著換ICD2;若還是一樣的結果;再檢查線路;若還是一樣的結果;換台電腦試試...
發表於: 2006/4/29 17:47
|
|||
|
Re: 有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
初級會員
|
這是當我在選擇晶片時ICD2會出現一些錯誤訊息如下
ICDWarn0020: Invalid target device id (expected=0x84, read=0x21) 請問這是什麼意思?
發表於: 2006/4/29 17:44
|
|||
|
有關ICD2燒錄問題~~
|
||||
---|---|---|---|---|
初級會員
|
各位大大你好,我目前使用PIC18F452, 要使用ICD2燒錄,但是出現無法抹除,不曉得有沒有要注意的地方還是怎樣?以下是我操作的訊息!
當我按下抹除後出現的訊息,本以為成功抹除 MPLAB ICD 2 Ready Erasing Target Device... ...Erase Succeeded MPLAB ICD 2 Ready Erasing Target Device... ...Erase Succeeded MPLAB ICD 2 Ready 但是使用VERIFY檢查後出現了 Blank Checking... ...Program Memory ICD0161: Verify failed (MemType = Program, Address = 0x0, Expected Val = 0xFFFF, Val Read = 0xEF48) ...Device not blank MPLAB ICD 2 Ready 請各位大大指點迷津!謝謝
發表於: 2006/4/29 17:26
|
|||
|