Re: 換了 c18 v3.0版本之後出現的警告訊息
|
||||
---|---|---|---|---|
高級會員
|
又搞烏龍,警告訊息還是存在,有人知道怎麼消除嗎?
發表於: 2006/7/5 10:55
|
|||
|
換了 c18 v3.0版本之後出現的警告訊息
|
||||
---|---|---|---|---|
高級會員
|
我的config bits 是寫死在code裡的,今天把c18換成 3.0版的
但是卻出現 cp_4、cp_5... code protect 被打開,不能進debug mode ,不過我用的pic18f8520根本就沒cp_4這些 code protect @@" 重點是除了警告訊息之外,還是能正常動作(debug mode).., 誠請指導。 mplab ide v7.31 原本c18 用 v3.02 差六天到期移除安裝同事的 v3.00 ICDWarn0042: Protect bit (CP_4 : Code Protect 10000-13FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (CP_5 : Code Protect 14000-17FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (CP_6 : Code Protect 18000-1BFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (CP_7 : Code Protect 1C000-1FFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_4 : Table Write Protect 10000-13FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_5 : Table Write Protect 14000-17FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_6 : Table Write Protect 18000-1BFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_7 : Table Write Protect 1C000-1FFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_4 : Table Read Protect 10000-13FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_5 : Table Read Protect 14000-17FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_6 : Table Read Protect 18000-1BFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_7 : Table Read Protect 1C000-1FFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting?
發表於: 2006/7/5 10:41
|
|||
|