:::
Browsing this Thread:
1 Anonymous Users
|
Re: 換了 c18 v3.0版本之後出現的警告訊息
|
||||
|---|---|---|---|---|
|
中級會員
 
|
如果沒記錯，C18 v3.00好像有一些問題。比如說：有一些PROCESSOR系列裏有幾個幾種-記憶体較大的幾種，和記憶体較小的幾種。V3.00的問題就是把一些記憶体較小的幾種誤當成記憶体較大的幾種來處理。
當然，最直接的解決方法是提升版本。不過如果在別無選擇的情狀下，你可以用ASM來做CONFIG。如果沒記錯，ASM好像沒有這一類的問題。
發表於: 2006/7/5 15:52
|
|||
|
||||
|
Re: 換了 c18 v3.0版本之後出現的警告訊息
|
||||
|---|---|---|---|---|
|
高級會員
|
又搞烏龍，警告訊息還是存在，有人知道怎麼消除嗎？
發表於: 2006/7/5 10:55
|
|||
|
||||
|
換了 c18 v3.0版本之後出現的警告訊息
|
||||
|---|---|---|---|---|
|
高級會員
|
我的config bits 是寫死在code裡的，今天把c18換成 3.0版的
但是卻出現 cp_4、cp_5... code protect 被打開，不能進debug mode ，不過我用的pic18f8520根本就沒cp_4這些 code protect @@" 重點是除了警告訊息之外，還是能正常動作(debug mode)..， 誠請指導。 mplab ide v7.31 原本c18 用 v3.02 差六天到期移除安裝同事的 v3.00 ICDWarn0042: Protect bit (CP_4 : Code Protect 10000-13FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (CP_5 : Code Protect 14000-17FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (CP_6 : Code Protect 18000-1BFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (CP_7 : Code Protect 1C000-1FFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_4 : Table Write Protect 10000-13FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_5 : Table Write Protect 14000-17FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_6 : Table Write Protect 18000-1BFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (WRT_7 : Table Write Protect 1C000-1FFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_4 : Table Read Protect 10000-13FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_5 : Table Read Protect 14000-17FFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_6 : Table Read Protect 18000-1BFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting? ICDWarn0042: Protect bit (EBTR_7 : Table Read Protect 1C000-1FFFF) is enabled. MPLAB ICD 2 will not enter debug mode in this configuration. Do you wish to disable this setting?
發表於: 2006/7/5 10:41
|
|||
|
||||
You can view topic.
你 不可以 發起新主題
You cannot reply to posts.
You cannot edit your posts.
You cannot delete your posts.
You cannot add new polls.
You cannot vote in polls.
You cannot attach files to posts.
You cannot post without approval.
You cannot use topic type.
You cannot use HTML syntax.
You cannot use signature.
You cannot create PDF files.
You cannot get print page.
